"A" Parameters Reference Chart

Acceleration Rate 1

• Determines the amount of time it will take for the drive to accelerate from 0 to 60 Hz
• A3 determines when this rate will be used

Acceleration 1 Time

• Default acceleration rate between speeds
• Determines the default time to accelerate from 0 to 60 Hz.
• Alternate "C" parameter* setting is C11

• Determines the amount of time it will take for the drive to accelerate from 0 to 60 Hz
• A3 determines when this rate will be used

CXR/MSM-R(P)

• Acceleration mode that determines when parameters A1 and A2 are applied
• Available modes differ between drive models. Refer to your drive's manuals for descriptions of each mode.

• Determines the amount of time it will take for the drive to decelerate from 60 to 0 Hz
• A7 determines when this rate is used (should be the longest time)

• Default deceleration rate between speeds
• Alternate "C" parameter* setting is C41

• Determines the amount of time it will take for the drive to decelerate from 60 to 0 Hz
• A7 determines when this rate is used

• Deceleration rate to stop from 60 Hz to stop
• Alternate "C" parameter* setting is C42 (limited by CL5 setting)

• Determines the amount of time it will take for the drive to decelerate from 60 to 0 Hz
• A7 determines when this rate is used (should be the shortest time)

• deceleration rate to reverse plug
• Alternate "C" parameter* setting is C43

Adjustable from 0.1 - 60 sec

• The deceleration rate used by drive. Determines when deceleration rate 1 (A4), deceleration rate 2 (A5), and deceleration rate 3 (A6) will be used (in each of these modes A4 is assumed to be the longest time and A6 the shortest)
• Available modes differ between drive models. Refer to your drive's manual for descriptions of each mode.

• Increases the torque at low frequencies. During low frequency output, the voltage output of the drive will increase by the amount set.
• This value also determines the minimum voltage for the Pulse Start and DC Injection feature (If the values in L31 or L33 are lower than A8 then A8's values will be used)

• Determines which of the different pendant control schemes will be used.
• Available modes differ between drive models. Refer to your drive's manual for descriptions of each mode.

• Speed adjustments for pendant control schemes
• See parameter C20* in manual for complete description of each mode

• If this value is positive the drive frequency will increase to that value in the forward direction
• If the value is negative, the drive's frequency will increase by the absolute value of the stored amount in the reverse direction
• This is a useful feature if the motor experiences more drag in one direction than in another (ie. a hoist,  in such a case compensate the drag by increasing the frequency output of the drive in the direction that experiences the drag)

• Sets the low speed setting of the drive
• This is invoked when either the forward or reverse terminal is activated

• Adjustable from 0.0 -120 Hz (MSM-R(P))
• Adjustable from 0.0 - 120 Hz (CXR)

• Default speed, usually low speed
• Alternate "C" parameter* setting is C21**

• Sets the second speed setting of the drive
• Usually invoked when the S2 terminal is activated

• Adjustable from 0.0 -120 Hz (MSM-R(P))
• Adjustable from 1.0 -120 Hz (CXR)

• Default setting associated with input S2
• Alternate "C" parameter* setting is C22**

• Sets the third speed setting of the CXR
• Usually invoked when the S3 terminal is activated

• Speed setting associated with input S3
• Alternate "C" parameter* setting is C23**

• Sets the fourth speed setting of the CXR
• Usually invoked when the S4 terminal is activated

• Speed setting associated with input S4
• Alternate "C" parameter* setting is C24**

• Sets the fifth speed setting of drive
• This speed is usually invoked when the S5 terminal is activated

• https://www.peinfo.com/operation-manual-request/Adjustable from 0.0 -120 Hz (MSM-R(P))
• Adjustable from 1.0 -120 Hz (CXR)

• Speed setting associated with input S5
• Alternate "C" parameter* setting is C25**

• Used with a potentiometer (see A9 mode 3 in manual)
• Sets the frequency the drive will output when potentiometer is turned to its upper limit

• Determines the maximum output range to which Analog 1 can be set
• Alternate "C" parameter* setting is C31

Adjustable 0.0 - 320 Hz